| Name | Needle Nose Pliers – Standard Jaws |
| Lead Time | 0-3 days |
| Competitor | ;1450-30;401775;40-1775;KM48245;4017-75;1450-30_4017-75; |
| Specialty | Neuro, Ortho & Spine-Wire/Pin Cutters & Pliers |
| Material Finish | Stainless Steel |
| Grade | Premium Operating Room |
| Units of Measurement | Each |
| Manufacturer | Shazira International |
| Sterility | Non-Sterile |
| Usage | Reusable |
Needle Nose Pliers – Standard Jaws
standard, 5-1/2″ (14.0 cm)Needle Nose Pliers are crafted for use in manipulate of surgical wire such as k-wire. Wire is a widely used accessory in surgical interventions because it can be used to approximate a fracture and speed up the healing process or it can be inserted through the skin and bone to give increased traction. These pliers can be used to twist and manipulate the wire into whatever orientation is required. Additionally this instrument of a standard pattern and is available with either smooth jaws or serrated jaws to satisfy any surgical scenario or surgeon preferences.
SKU:
SI-01-1299
Category: Wire & Pin Management Instruments
Description
Reviews (0)
Be the first to review “Needle Nose Pliers – Standard Jaws” Cancel reply
Related products
Double Action Pin Cutter
SKU:
SI-01-1273
side cutting maximum capacity 1?8" (3.2mm), 9-1/2" (24.1 cm)Double Action Pin Cutter is an instrument ideally suited for use in surgical procedures that require the insertion of surgical pins and subsequently the clipping and resizing of their lengths. Many orthopedic and neurosurgical spinal procedures require the insertion of pins to stabilize a repaired fracture or an inserted graft. These pins often need to be trimmed to allow them to be set at a more appropriate length for the individual patient and these cutter can be used for that. This instrument is double action and is side cutting and has a maximum capacity of 3.2 mm.
Lineman Pliers
SKU:
SI-01-1290
side-cutting, maximum capacity 1.6 mm, 8-1/2" (21.6 cm)Â Lineman Pliers are a multi-purpose instrument designed for use in surgical procedures to manipulate wire. Many orthopedic surgeries such as fracture repair depend on the use of wire to approximate the fragments and accelerate the healing process. Wires must be manipulated and wrapped to fit the particular scenario where they are needed and these pliers are built for that. They features tungsten carbide jaws and are side cutting with a maximum capacity of 1.6 mm.
Hercules-Type Front & Side Cutter
SKU:
SI-01-1284
replaceable tungsten carbide blades w/ integrated rubber jaws, for max 1.6 mm drill wire, 7" (17.8 cm)Hercules-Type Front & Side Cutter is a multi-purpose instrument suitable for a variety of orthopedic procedures in which wire or pins are used. Fracture repair procedures can utilize pins to set the bone fragments or can be approximated by wrapping wire around. This instrument is ideally suited for manipulation of wire and pins as well as cutting them either from a front or a side approach. This instrument features replaceable tungsten carbide jaws with integrated rubber jaws for a maximum 1.6 mm drill wire.
End Cutter – Double Spring, Large, Tungsten Carbide
SKU:
SI-01-1275
tungsten carbide jaws, double-action, maximum capacity 3?32" (2.5mm), 8-1/2" (21.6 cm)Â End Cutter is a unique instrument designed for cutting of surgical pins or wire. Many orthopedic and neurosurgical spinal procedures require the use of such stabilization accessories to prevent trauma during recovery and confer additionally stability. This instrument is particularly well suited for end cutting which allows it to be made flush with the edge of bone or other tissue ares where it is being used. Additionally this end cutter is double-action and features tungsten carbide jaws with a maximum capacity of 3/32".
Flush Wire Cutter – Tungsten Carbide
SKU:
SI-01-1280
tungsten carbide jaws, double-action, front & side cutting, cuts up to 1/16" (1.7 mm) diameter hard wire, 7" (17.8 cm)Â Flush Wire Cutter is an instrument designed for use in cutting wires during surgical procedures. A variety of procedures require the insertion of wire to stabilize an inserted graft or fracture repair. This decreases potential for trauma and increases the speed of healing. This cutter features double-action tungsten carbide jaws that allow for precise cuts on wire up to 1.7 mm diameter. This instrument can be used for both front and side cutting.
End Cutter – Barrel Spring, Small, Tungsten Carbide
SKU:
SI-01-1274
tungsten carbide jaws, w/ coil spring, maximum capacity 1/16" (1.7mm), 6" (15.0 cm)Â End Cutter is a unique instrument designed for cutting of surgical pins or wire. Many orthopedic and neurosurgical spinal procedures require the use of such stabilization accessories to prevent trauma during recovery and confer additionally stability. This instrument is particularly well suited for end cutting which allows it to be made flush with the edge of bone or other tissue areas where it is being used. Additionally this end cutter features tungsten carbide jaws and has a maximum capacity of 1/16".
Flat Nose K-Wire Pliers
SKU:
SI-01-1276
serrated jaws, 7" (17.8 cm), 3.0 mm tip Flat Nose K-Wire Pliers are instruments ideally suited for use with surgical K-wire. This wire can be used for temporary fixation in some procedures thus giving support through the healing process and then can be removed. Additionally K-wire can be used in permanent fixation and can also be passed through the skin and bone to provide direct traction to the bone itself. In all of this surgical scenarios this instrument will be of optimal function in manipulation and handling of the wire and features serrated jaws which gives added hold and grip to prevent slipping. This instrument is available with or without a grooved jaw.
Cannulated Pin Cutter
SKU:
SI-01-1268
end cutting, max cutting capacity 1/16" (1.7 mm), 7-1/2" (19.0 cm)Â Cannulated Pin Cutter is a specialized instrument ideally suited or use in procedures of fracture repair or other procedures where a graft is set with a pin. The unique design of this cutter allows for effective end cutting. The entire head portion of the pin can be inserted into the cutter and clipped flush and the remaining clipped portion remains held in the cutter to be removed. The maximum cutting capacity of this pin cutter is 1.7 mm.

Reviews
There are no reviews yet.